Getting Started with Plumbing Basics for Bathtub Installation

Browse Our Site

We have come across this post involving How to Install a Bathtub: Install an Acrylic Tub and Tub Surround down the page on the internet and figured it made perfect sense to talk about it with you over here.


A Step-by-Step Guide to Installing a Bathtub
Setting up a tub isn't precisely brain surgery, yet it does call for solid plumbing, woodworking, as well as occasionally, tiling skills. Changing an old bathtub with a brand-new one is additionally a moderately challenging task. If the old bathtub is conveniently obtainable, the task can relocate speedily; if you need to open up a wall surface to remove the old tub as well as place the new tub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will certainly require a helper to move out the old bathtub as well as set in the new one. Make certain you have actually qualified yourself for the task as well as are comfortable trying it. Instead of working with a specialist to take over a halfway-completed job, it is much better to consider using one before you begin. Possibilities are you may require an expert plumber to make tube connections.
This short article will aid you set up a brand-new bath tub in your restroom if you have already gotten a new tub and don't require to change the arrangement of your previous water system pipes.
Your devices and product list should make up the following:
  • New Bathtub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Blade

  • Tape Measure

  • Pipe Caps


  • Planning for the Installment


    To start with, the sustaining frame supplied with the bathroom ought to be fitted (if required) according to the producer's guidelines. Next off, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is important to see to it that if the faucet comes with a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets unit to avoid stress on the tub.
    Fit the adaptable tap connectors to the bottom of both faucets making use of 2 nuts and also olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet through the hole in the bathroom. Use the nut supplied by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next off, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. See to it you use every one of the supplied washers.
    Link the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom need to currently be ready to be fitted in its final setting.

    Removing Old Taps


    If you require to change old taps with new ones as a part of your installation, then the first thing you need to do is detach the supply of water. After doing so, activate the faucets to drain pipes any type of water continuing to be in the system. The procedure of getting rid of the existing faucets can be fairly bothersome because of the restricted access that is frequently the instance.
    Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipelines to the taps. Have a towel all set for the staying water that will certainly originate from the pipelines. Once the supply pipelines have been gotten rid of, make use of the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to stop the solitary faucets from transforming during this process. Once the taps have been eliminated, the holes in the bath/basin will need to be cleansed of any kind of old securing compound.
    Before moving on to fit the new faucets, compare the pipeline links on the old taps to the brand-new faucets. If the old taps are longer than the new taps, then a shank adapter is needed for the new faucets to fit.

    Mounting the Bath tub


    Making use of both wooden boards under its feet, position the tub in the needed placement. The wooden boards are handy in evenly spreading the weight of the tub over the area of the boards instead of concentrating all the weight onto 4 tiny factors.
    The next objective is to make certain that the bath tub is leveled all round. This can be attained by examining the level and changing the feet on the bathtub till the level reads degree.
    To install faucets, fit the bottom of the furthest flexible faucet port to the appropriate supply pipe by making a compression join; then do the very same for the other faucet.
    Activate the water system and also examine all joints as well as new pipework for leakages as well as tighten them if needed. Fill the tub as well as also examine the overflow electrical outlet and also the normal electrical outlet for leaks.
    Ultimately, deal with the bath paneling as defined in the supplier's instruction manual. Tiling and sealing around the bath tub ought to wait until the bath tub has been made use of at the very least when as this will certainly resolve it right into its final placement.

    Suitable New Touches


    If the tails of the new taps are plastic, then you will certainly require a plastic connector to avoid damages to the string. One end of the port fits on the plastic tail of the tap as well as the other end provides a link to the current supply pipes.
    If you need to fit a monobloc, then you will certainly require minimizing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
    Next off, position the tap in the mounting opening in the bath/basin making sure that the washing machines are in area in between the faucet and the sink. Protect the tap in place with the maker offered backnut. When the tap is securely in position, the supply pipes can be connected to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with typical faucet ports. The previous type ought to be linked to the tap finishes initially, tightening only by hand. The supply pipes can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been linked.

    Tiling Around the Bath tub


    In the area where the bath meets the tile, it is necessary to seal the joins with a silicone rubber caulking. This is important as the fitting can relocate enough to break an inflexible seal, creating the water to penetrate the wall surface between the bath as well as the tiling, bring about difficulties with wetness and also feasible leaks to the ceiling below.
    You can choose from a variety of coloured sealers to assimilate your components as well as installations. They are marketed in tubes as well as cartridges, and also can securing voids approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with twists of soaked paper or soft rope. Keep in mind to always fill the bath tub with water prior to securing, to enable the motion experienced when the bathtub is in usage. The sealer can split relatively very early if you do not consider this activity before securing.
    Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently offered on the market. It is suggested to fit the floor tiles utilizing water-resistant or water resistant adhesive and also grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    Installing A Bathtub

    Do you really like more info about A Step-by-Step Guide to Installing a Bathtub? Create feedback down the page. We'd be glad to know your insights about this blog entry. In hopes that you come back again before long. Those who enjoyed reading our post if you please make sure you remember to pass it around. Thanks for your time. Visit again soon.


    Leading plumbing expertise for emergencies.

    Leave a Reply

    Your email address will not be published. Required fields are marked *